When you use Ebay Contact Seller form - please do not hide your email address.
This adapter allows to connect a laptop IDE Hard Drive (mini 44pin)
directly to a desktop IDE cable (40 pin). It has a single piece board
design which is easy to attach & detach.
A must have for laptop hard drive cloning backup or recovery.
WORKS WITH ALL LAPTOP DRIVES
(Acer, Apple, Compaq, DELL, Fujitsu, Gateway, Hitachi, HP, IBM, Samsung, Sharp, Sony, Toshiba, ...)
Also works with all OS Versions (DOS, Windows 95, 98, NT, 2000, XP, Vista..., Linux, Mac)
INSTALLATION INSTRUCTIONS
1. Leave your desktop system drive in PRI MASTER
2. connect laptop drive to SEC channel
3. Make sure no other devices attach to SEC cable
4. In this config - laptop drive will be SEC MASTER
5. Boot into BIOS and autodetect the new configuration
6. Either leave in auto-detect for all 4 drives or go through all 4
7. Make sure SEC MASTER is Autodetect or set for laptop drive
8. Make sure SEC SLAVE is set to NONE
9. Boot into your OS (from PRI MASTER)
* If laptop drive has XP NTFS partitions; and desktop OS is Win2K - you may
experience bluescreens. XP NTFS partitions are more advanced.
You may need to upgrade your Win2K host to WinXP to be able to access
such XP NTFS partitions.
PIN 1 should follow from the IDE cable through
the adapter to the drive as shown on the picture below
Most laptops have a slide-in attachment on the mini-IDE hard drive connector.
That attachment is not permanently connected and should be detached before
using the adapter. Picture below demonstrates the most common attachment
used with HP and DELL laptops:
IMPORTANT: You must connect this
adapter correctly as shown on the picture above. Incorrect connection
will damage the drive. Please follow the diagram for proper connection.
Pin 1 must follow through IDE cable to the laptop drive as indicated.
Master/Slave pins must never be connected or spanned by the adapter.
| Warranty |
 |
|
1. NEW ITEMS
New items are covered by 1-month full refund warranty and by
6-months extended replacement warranty. If you do not like your
item for any reason - you can return it back to us within the
warranty period at your own expense and we will provide a
refund or replacement.
2. USED ITEMS
Used/off-lease/refurbished items are not covered by full
refund warranty. If you wish to return it back to us, you
will only be refunded the item charge and not the S&H charge.
They are covered by a 3-month replacement warranty. As with
new items - you have to return the item back to us at your
own expense.
We label our items with special codes. Do not remove these codes.
If we determine that you send us an item which we did not sell
you, or if the item is missing our codes, we will not replace it.
If you need your item back, full S&H charge will be applied again.
|
| Payment |
|
We accept PAYPAL, Check or Money Order
California residents must pay 7.75% sales tax
- taxes apply to order total including s&h
- no tax for shipping outside California
1. Do not paypal right away.
2. We will send you a link to your on-line invoice in our system.
3. Please enter your address and pay through that on-line invoice.
4. It may take up to an hour for the on-line invoice to reflect items you purchase.
5. To get discounted rate for multiple items purchased from us,
you must wait for all items to be added to the on-line invoicebefore
you pay. If you do not - your items may or may not ship together
and we will not refund the difference.
If you do not receive an email from us, please proceed to pay here:
|
| Shipping |
|
Shipping & handling is $3.84 inside the USA.
Additional same
adapters
add $2.84 to s&h
No shipping outside the USA unless you are ordering over 20 items from us.
APO and FPO addresses are OK if they validate via THIS USPS FORM
Most orders ship via USPS with average delivery time 2-5 days.
Some very large orders (20lb or more) may ship via UPS.
When providing an address - make sure it is deliverable by
the USPS. If it is returned back to us as non-deliverable
we will withold the S&H amount.
|
|
)
